Únete al equipo Blanchard..
Solicitar ahora
Cat C9 ACERT engines are the ideal solution for your demanding operations in the oilfield. Decades of field operation and intense research and development allow Cat C9 ACERT engines to deliver excellent performance with low operating costs and emissions. Equipment powered by C9 ACERT engines include workover rigs, pump skids, acidizing units, cementing units, coil tubing units, and hydraulic power units. Cat engines are backed by the worldwide network of Cat dealers ready to support your operation with technical support, service, parts, and warranty. C9 ACERT engines, with ratings: 205-280 bkW (205-375 bhp) @ 2200 rpm, meet China Stage II, EPA Tier 3 equivalent, EU Stage IIIA equivalent emission standards. U.S. EPA Tier 3 equivalent and EU Stage IIIA equivalent ratings are available using U.S. EPA and EU Flexibility. They are also available in other regulated and non-regulated areas.
Solicitar presupuestoMaximum Rating375BHP
Displacement538in³
Minimum Rating205BHP
Governor and ProtectionElectronic (ADEM™ A3)
AspirationTurbocharged-Aftercooled
Flywheel and Flywheel HousingSAE 1 or 2
Flywheel Teeth113 (SAE 1), 134 (SAE 2)
Rotation from Flywheel EndCounterclockwise
Stroke5.8in
Bore4.41in
EmissionsEPA and CARB Non-Road Tier 3, EU Stage IIIA, IMO Tier II
Length43in
Width32.6in
Height40.3in
Weight1578lb
Lube Oil System - Refill8gal (US)
Cooling System3.7gal (US)
Estándar
Turbocharger, separate circuit (SCAC) or remote (REMAC) aftercooler
Single, right-side, center-mounted turbo with water-cooled turbine housing
Air inlet 101.6 mm (4 in) connection type
Opcional
Air cleaners
Precleaner
Air inlet elbow
Air shutoffs
Estándar
Electronic governing, PTO speed control
Programmable ratings
Cold mode start strategy
Automatic altitude compensation
Fuel cooled ECU
Power compensation for fuel temperature
Programmable low and high idle
Electronic diagnostics and fault logging
Programmable monitoring system (engine speed, temperature, pressure)
J1939 broadcast (diagnostic and engine status)
Electronic installation kit (connectors, PINS, sockets) (nonhazardous environment only)
Certified electrical control system (hazardous environment only)
Derated engine: automatic ambient temperature compensation
Estándar
Thermostats and housing, RH forward-facing outlet — 51 mm (2.01 in) connection
Jacket water pump — belt-driven, centrifugal
Water pump — inlet RH facing downward 63 mm (2.48 in)
Opcional
Radiators
Radiators
Fans f/u/w radiator packages
Coolant level sensor
Fan drive mountings, adapters, pulleys
Vee belts for customer-supplied radiators
Suction fans and blower fans
Water inlet elbows
Dry charge coolant conditioners
Estándar
Exhaust manifold — water-cooled
Single, center right-side mounted turbo with water-cooled turbine housing
Rear facing turbo exhaust 81.8 mm (3.22 in.) connection, non V-band clamp
Opcional
Flexible fitting
Turbocharger exhaust outlet adapters
Elbows, flange, pipes, clamp
Rain caps
Manifolds
Mufflers
Estándar
Mandatory selection of: SAE No. 1 or SAE No. 2 flywheel and housing, SAE standard rotation
Opcional
Crankshaft seal
Estándar
HEUI fuel system
Fuel filter — secondary, LH (2-micron high performance)
Fuel transfer pump — left front
Fuel priming pump — left front
Opcional
Flexible fuel lines
Water separator and fuel filters
Fuel cooler
Estándar
Crankcase breather — LH
Crankcase fumes disposal with integrated service indicator, LH
Oil cooler — RH
Oil filter — RH
Oil pan — front sump
Oil filler — top mounted
Oil level gauge — LH side
Oil pump — gear-driven
Oil valve sampling
Preservation of turbocharger, flywheel, and crankcase
Opcional
Oil pan
Drain and cover
Oil level gauges
Remote oil filter
Oil fillers
Lubricating oil
Fumes disposal
Fumes disposal mounting
Estándar
Crankshaft drive pulley — 2 grooves, 190 mm (7.5 in) diameter, 22.3 mm (7/8 in) wide
Opcional
Enclosed clutch
Clutch supports
Flywheel stub shaft
Hydraulic pump drives
Hydraulic gear pumps
Pulley
Estándar
Vibration damper
Lifting eyes
Automatic variable timing — electronic
Literature
Opcional
Tool set
Estándar
Flywheel housing and flywheel
Throttle position sensor and/or throttle control (non-hazardous environment only)
Primary filter/water separator
Turbo orientation
Opcional
Air compressor governor
Opcional
Charging alternators
Alternator mountings and pulleys
Alternator belt tensioner
Opcional
IMO Certification
Opcional
Gauges and instrument panels
Interconnect harnesses
Voltmeters
Gauge mounting
Ammeter
Opcional
Structural steel base
Front and rear engine supports
Opcional
Starting aids
Electric starting motors — 12V and 24V
Battery sets — 12V and 24V (dry)
Battery cable
Opcional
Transmission cooler
Rellene este formulario para obtener un presupuesto sobre el equipo que le interesa.
