it's catit's single

C15 ACERT™ Dry Manifold Engine

C15 ACERT™ Dry Manifold Engine

Cat C15 ACERT engines are the ideal solution for your demanding operations in the oilfield. Decades of field operation and intense research and development allow Cat C15 ACERT engines to deliver excellent performance with low operating costs and emissions. Equipment powered by C15 ACERT engines include workover rigs, pump skids, nitrogen units, acidizing units, cementing units, blenders, and hydraulic power units. Cat engines are backed by the worldwide network of Cat dealers ready to support your operation with technical support, service, parts, and warranty. C15 ACERT engines, with ratings: 328-444 bkW (440-595 bhp) @ 1800-2100 rpm, meet China Stage II, U.S. EPA Tier 3 equivalent, EU Stage IIIA equivalent emission standards. They are available using U.S. EPA and EU Flexibility, and for other regulated and non-regulated areas.

Request a Quote

Maximum Rating595BHP

Displacement928in³

Minimum Rating440BHP

Governor and ProtectionADEM A3

AspirationTurbocharged-Aftercooled

Flywheel and Flywheel HousingSAE No. 0 or SAE No. 1

Flywheel Teeth136 (SAE 0), 113 (SAE 1)

Rotation from Flywheel EndCounterclockwise

Stroke6.75in

Bore5.4in

EmissionsEPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA

Length54.2in

Width36.5in

Height48.3in

Weight2743lb

Cooling System5.5gal (US)

Standard

Single turbocharger, mid-mounted, inlet 152.4 mm (6 in), hose connection

Optional

Air cleaners

Precleaners

Air lines

Air inlet gasket

Standard

Electronic governing, PTO speed control

Programmable ratings

Cold mode start strategy

Automatic altitude compensation

Power compensation for fuel temperature

Programmable low and high idle and TEL

Electronic diagnostics and fault logging

Engine monitoring and protection system (speed, temperature, pressure)

J1939 Broadcast (diagnostic, engine status, and control)

Standard

Thermostats and housing — outlet vertical

Jacket water pump — gear-driven, centrifugal, RH

RH front water pump inlet

All plugs/fittings are STOR for lines gp water

Optional

Radiator — installed

Radiator — ship loose

Fan drive f/u/w Caterpillar installed radiator

Fan drives for customer-supplied radiators

Fan height instructions

Vee belts for customer-supplied radiators

Aftercooler lines f/u/w Caterpillar installed radiator

Rear-facing exhaust

Aftercooler lines

Suction fan adapters — attaches fan to fan pulley

Blower fan adapter — attaches fan to fan pulley

Blower fan

Suction fan

Fan belt tightener

Coolant level sensor

Dry charge coolant conditioners

Dry charge coolant conditioner element

Standard

Exhaust manifold — dry

Front turbo exhaust

Full marmon connection, maximum load 10 kg for direct connection to turbo

Optional

Turbo exhaust connection

Flexible fitting

Elbows

Flanges

Dry elbow

Standard

See Mandatory Options

Standard

MEUI system

Fuel filter, secondary, mid-mount (LH 2 micron high performance)

Fuel transfer pump, LH front

Fuel priming pump, LH mid-mount

Fuel sample valve, mounted on fuel filter base

Standard

Crankcase breather — rear valve cover

Oil cooler — RH

Oil filter — RH

Oil pan — front sump

Oil filler — LH front

Oil dipstick — LH front

Oil pump

Oil valve sampling — on oil filter base

Standard

Front support (shipping only)

Standard

Crankshaft pulley, 203.2 mm (8 in), 3 grooves 292.1 mm (11.5 in) 1 groove, all 15.9 mm (.63 in) width

Hydraulic pump drive, SAE A, 11 tooth

Standard

Vibration damper

Paint — Cat yellow

Lifting eyes

Automatic variable timing, electronic

Electronic installation kit 70-pin connector (connectors, pins, sockets)

Literature group owner and operator

Standard

Throttle position sensor

Exhaust system — front or rear

Flywheel housing or rear PTO

Primary filter/water separator

Optional

Transmission cooler

Tool set

Optional

Air chambers

Air compressor governor

Optional

Charging alternators

Alternator mountings

Alternator wiring

Circuit breaker mountings

Alternator belt guard

CONTACT US

REQUEST A QUOTE

Complete this form to get a quote on the equipment you are interested in.

    This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

    What You Get: A phone call from a rep or agent. A cost estimate for your machine or the project. An in-person consultation if necessary.