it's catit's single

Cat C32 ACERT Generator Set (IMO II)

Cat C32 ACERT Generator Set (IMO II)

C32 ACERT generator sets incorporate a separate circuit aftercooling system (SCAC) for all configurations. The primary advantage of the SCAC systsem is reduced aftercooler corrosion since no sea water circulates through the aftercooler. Many other improvements on these engines contribute to minimizing owning and operating costs. The IMO II and EU Stage IIIA compliant ratings are available with heat exchanger or keel cooled options. Heat exchanger configurations have an optional front mounted sea water pump.

Request a Quote

Minimum Rating550 eKW (688 kVA)

Maximum Rating940 ekW (1175 kVA)

Frequency50 Hz or 60 Hz

Speed1500 rpm (50 hz) or 1800 rpm (60 hz)

Emissions/Fuel StrategyIMO II

AspirationTwin Turbocharged-Aftercooled




Governor TypeElectronic

Fuel SystemDiesel

Engine ModelVee 12, 4-Stroke-Cycle Diesel

Excitationpermanent magnet (PMG)


Number of Poles4

Number of Bearings2 roller bearings

Number of Leads6

InsulationClass H

Voltage Regulation± 0.5% (steady state)

Frame Size1423, 1467

IP RatingDrip Proof IP 23*

AlignmentClosed-coupled adapter

Wave Form Deviation - Line to Line< 3.0%

Voltage RegulatorCat® Digital Voltage Regulator (CDVR)

Telephone Influence Factor (TIF)< 50




Weight - Estimated15721lb


Separate circuit after-cooled (SCAC)

Turbocharger, jacket water cooled

Turbocharger inlet, 152 mm (6 in) OD straight connection


Air Inlet Cleaner

Closed Crankcase Ventilation

Air inlet adapter


If an EMCP panel or MGCP option is not chosen as optional equipment, then start/stop controls must be provided by the customer

Electronic diagnostics and fault logging

Engine Protection Mode for extended ambient conditions

Electronic fuel/air ratio control


Load Sharing Attachment


Separate Circuit After-Cooling (SCAC) for Heat Exchanged (HEX) & Keel cooled engines

Jacket Water (JW) and SCAC Heat Exchangers Shell & Tube for HEX cooled engines

SCAC pump, gear driven

Jacket water pump, gear driven

Sea water pump, bronze impeller, gear driven, for HEX cooled engines only

Jacket water HEX with Sea water pump Connections: 76.2 mm (3in) ID Standard

4 Bolt ANSI Flange Connection

Jacket water HEX without Sea water pump Connection: 2.5" hose barb connection (inlet), 76.2 mm (3in) ID Standard 4 Bolt ANSI Flange (outlet)

Keel Connections: 76.2 mm (3in) ID Standard 4 Bolt ANSI Flange Connection

SCAC and JW shunt tanks for maintaining proper Pump inlet pressures


Water-cooled exhaust manifold & turbocharger

4 Bolt 130 mm (5.12 in) diameter flanged outlet


Dry Elbows

Flexible Fitting



Muffler Spark Arresting

Rain Cap


Flywheel Housing, SAE No. 0

Flywheel, 18 inch, 136 teeth

SAE standard rotation


Duplex Fuel Filters, Spin-on, RH service

Fuel connections size: Supply JIC Deg -10 (7/8 - 14), Return JIC 37 Deg -8 (3/4 -16)

Plate-type fuel cooler installed behind Aftercooler Shunt Tank

Fuel transfer pump, gear driven

Manual fuel priming pump


Water Separator


SR5 form wound

2 roller bearings

Permanent magnet excitation

4 pole, 6 leads, Series Star connected

Caterpillar's Digital Voltage Regulator (CDVR)

Marine Class H insulation, Class F temperature rise

Surface mounted platinum (PT100) 3-wire RTDs, 2 per phase on stator and one each on support bearings

Anti-condensation space heaters (2 elements - 240 VAC, 1000 Watts

IP23 Protection suitable for use with Fixed Water Based Local Application Fire Fighting Systems (FWBLAFFS)

System IV insulation for harsh environment protection


Simplex oil filters, RH service

Deep sump oil pan

RH service oil filler locations

RH service dipstick

Oil pump, gear driven


Duplex Oil Filters, Sump Pump


Formed C-channel rails, 300mm (11.81in) height

Six shipped loose combined helical spring/rubber isolators for installation below package base


Front damper guard

Common electrical bonding point on HEX and KEEL cooled engines


Remote Panels

MCS Controller

Power analyzer module

oil level, exhaust temperature, air starting pressure, heat exchanger pressure sensors


Battery Chargers, Charging Alternators


Fuel and Oil Shielding


Electric Starting Motors - Single 24 Volt

Air Starting Motor

Dual Starting Motors (Electric and Air)

Air Start Accessories

Starting Aids - JW Heaters

Battery Sets - 24 Volt - Dry



Complete this form to get a quote on the equipment you are interested in.

    This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

    What You Get: A phone call from a rep or agent. A cost estimate for your machine or the project. An in-person consultation if necessary.