Join the Blanchard Team..
Apply Now
Cat C7 ACERT engines are the ideal solution for your demanding operations in the oilfield. Decades of field operation and intense research and development allow Cat C7 ACERT engines to deliver excellent performance with low operating costs and emissions. Applications powered by C7 ACERT engines include pump skids, acidizing units, cementing units, coil tubing units, and hydraulic power units. Cat engines are backed by the worldwide network of Cat dealers ready to support your operation with technical support, service, parts, and warranty. C7 ACERT engines, with ratings: 153 – 224 bkW (205 – 300 bhp) @ 2200 rpm meet IMO Tier II, U.S. EPA Marine Tier 3, EPA Non-road Tier 3 equivalent and EU Stage IIIA equivalent emission standards. They are available using U.S. EPA and EU Flexibility, and for other regulated and non-regulated areas.
Request a QuoteMaximum Rating275BHP
Displacement442in³
Minimum Rating205BHP
Governor and ProtectionElectronic (ADEM™ A4)
RPM2200r/min
AspirationTurbocharged-Aftercooled
Flywheel and Flywheel HousingSAE 1, 2, or 3
Flywheel Teeth156 (SAE 1), 134 (SAE 2), 126 (SAE 3)
Rotation from Flywheel EndCounterclockwise
Stroke5in
Bore4.3in
EmissionsEPA & CARB Non-Road Tier 3, EU Stage IIIA, EPA Marine Tier 2, IMO Tier II
Length41.5in
Width29.8in
Height40.6in
Weight1386lb
Lube Oil System - Refill4.8gal (US)
Standard
Turbocharger, separate circuit (SCAC)
Single, right-side, center-mounted turbo with water-cooled turbine housing
Air inlet, RH side, rear facing, 101.6 mm (4 in.) connection type
Optional
Precleaner
Air Inlet elbow
Standard
Electronic governing, PTO speed control
Programmable ratings
Cold mode start strategy
Automatic altitude compensation
Fuel cooled ECU
Power compensation for fuel temperature
Programmable low and high idle
Electronic diagnostics and fault logging
Programmable monitoring system (engine speed, temperature, pressure)
J1939 broadcast (diagnostic and engine status)
Certified electrical control system
Derated engine: automatic ambient temperature compensation
Standard
Thermostats and housing, front-facing outlet — 51 mm (2.01 in) connection
Jacket water pump — belt-driven, centrifugal
Water pump — inlet RH front vertical inlet (pointing down) — 63 mm (2.48 in)
Optional
Water outlet elbow
Coolant conditioner
Standard
Single, right-side, center-mounted turbo with water-cooled turbine housing
Exhaust manifold — water-cooled
Front turbo exhaust
Standard
Mandatory selection of: SAE No. 1, SAE No. 2, or SAE No. 3 flywheel and housing SAE standard rotation
Optional
Crankshaft seal
Standard
HEUI fuel system
Fuel filter — secondary, LH front (2-micron high performance)
Fuel transfer pump — left front
Fuel priming pump — left front
Standard
Crankcase breather — top rear
Crankcase fumes disposal — RH
Oil cooler — RH
Oil filter — RH
Oil pan — front sump, 31 L (33 qt) oil change capacity
Oil filler — front top valve cover
Oil level gauge — LH rear
Engine oil pump — gear-driven
Oil valve sampling, RH
Optional
Oil pans
Drain and cover
Remote oil filters
Lubricating oils
Standard
Crankshaft drive pulley — 2 grooves, 190 mm (7.5 in) diameter, 22.3 mm (0.88 in) wide
Standard
Vibration damper
Lifting eyes
Literature
No paint
Optional
Tool set
Standard
Flywheel housing and flywheel
Primary filter/water separator
Turbo orientation
Optional
IMO certification
Optional
Gauges and instrument panels
Optional
Structural steel base
Engine support -- front and rear
Optional
Crankshaft pulleys
Complete this form to get a quote on the equipment you are interested in.
